VIDEO

Trälim

A wood glue that is water resistant and does a good job.

Den här produkten är just nu slut i lager och inte tillgänglig.

Artikelnr: Inte tillgänglig Kategori: Taggar: , ,

Gorilla wood glue is a waterproof and reliable glue for indoor and outdoor use, which provides a solid bracket on many different wood surfaces.
Gorilla wood glue is the water-based PVA glue that is easy to use and has the fastening strength that Gorilla is known for.
It dries with a natural color which is guaranteed to give you a clean and stylish joint for your work.

Säkerhetsdatablad


Applikatorer som förhindrar klumpbildning



Inomhus/utomhus



Vattenfast (D3)



Grepptid 20-30 min.

  • Get your work done quickly

Provides a strong attachment and needs a short drying time – only 20-30 min.

  • Inside Outside

D3 waterproof.

  • Versatile

Use on hardwood, softwood and composites.

  • Dry with a natural color.

It dries with a natural color which is guaranteed to give you a clean and stylish joint for your work.



Så här gör du
1. Förbered

Remove the application pipe to clear the glue lumps.
If the glue thickens or divides, shake vigorously until the correct texture is obtained.


2. Applicering

For best results, it is important that the wood surfaces are prepared before applying the glue.
For lamination, the surfaces should be smooth and without marks after machines, tears or notches.
Also be sure to avoid slippage and edge chipping.
How much glue is needed depends on many factors. Generally, a copious amount of glue can be applied to one of the surfaces.
On woods that are difficult to glue, a layer is laid on both surfaces.
Rub against the other surface to distribute the glue evenly on both surfaces.
Enough glue should be applied to get a small excess which will squeeze out when the surfaces are compressed.


3. Sammanpressning

The technique and type of compression that should be used is dependent on many factors: the type of joint, the type of wood, the moisture content of the material, the room temperature, the time used for composition and the nature of the surface.
Generally, enough pressure should be applied to get a small excess that exits when the surfaces are compressed properly.

Pressing time (how long the pressure must be applied): 20-30 minutes at room temperature.
The temperature must be above 13 ° C. Note that the pressing time can vary depending on the temperature, humidity and wood porosity.

Drying time (how long it takes to achieve full fastening strength): 24 hours


4. Rengöring/förvaring

Cleaning when the glue has not dried: Use a clean, damp cloth to wipe off excess glue.
Wipe as much as needed with the clean part of the cloth to remove any glue.
Grind as needed when the area has completely dried. Wash hands, skin and damp cloths with soap and warm water, then rinse.

Cleaning when the glue has dried: Use a putty, razor blade, or scraper to plan hardened glue from the surface, then grind as needed. Soak hands and skin with soap and warm water, then rinse.

Cleaning the bottle opening: Use a clean, damp cloth to wipe off excess glue after sealing.
If glue lumps cork the pipe again, remove the lid and push the lump backwards with a toothpick. Then rinse the lid in warm water.
To remove Gorilla wood glue from your hands, wash with soap and warm water.

The temperature during use should be above 13 ° C. Grind the surface before finishing it to reduce the adhesive exposure.
Not recommended for load-bearing structures or for permanent immersion in water or use below the water surface.

Close the lid after use. Store at room temperature (not below zero).
If the glue thickens or divides, shake vigorously until the correct texture is obtained.


Vanliga frågor

  • How do I remove Gorilla wood glue from my body or skin?

To remove Gorilla wood glue from your hands, wash with soap and warm water.

  • How do I remove Gorilla wood glue from a surface?

If the glue has not dried, use a clean, damp cloth to wipe off excess glue.
Wipe as much as needed with the clean part of the cloth to remove any glue.
Grind as needed when the area has completely dried.
To remove adhesive that has hardened, use a putty, razor blade, or scraper to plan the cured adhesive from the surface, then grind as needed.

  • Gorilla wood glue is too thick for what I need to do, can I thin this glue?

Gorilla wood glue, unlike Gorilla Glue, is a water based glue.
You can dilute Gorilla wood glue with water (no more is 5% weight).

  • Fäster Gorilla trälim på fläckade eller målade föremål?

Gorilla trälim är avsett för användning på lövträ, barrträ, kartong, kork och kompositträ.

  • Är Gorilla trälim säkert med mat?

Vi rekommenderar inte att Gorilla trälim, härdat eller ej, kommer i kontakt med mat.

  • Hur gör jag rent en tilltäppt spets?

För att göra rent flaskans spets används en ren, fuktad trasa för att torka av överskottslim efter försegling.
Om spetsen täpps till av torkat lim, ta av locket, dra av pipen och tryck klumpen baklänges med en tandpetare. Skölj sedan locket med varmt vatten.
Om det är svårt att dra upp munstycket används en tång eller sax som placeras vid basen på munstycket och vrids om något.

  • Vad gör jag om jag misstänker att en människa eller ett djur har fått i sig Gorilla trälim?

For medical emergencies, contact your doctor immediately. Call 112 in the event of a medical emergency. For emergency situations involving animals, contact your Veterinarian or animal specialist immediately.



RELATERADE PRODUKTER

Du gillar kanske också…